A Computer hardware and components forum. ComputerBanter.com

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » ComputerBanter.com forum » General Hardware & Peripherals » Homebuilt PC's
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Can I make my power supply fan turn faster?

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old July 10th 18, 12:18 PM posted to alt.comp.hardware.pc-homebuilt
external usenet poster
Posts: 723
Default Can I make my power supply fan turn faster?

Steve Hough wrote:
Rene Lamontagne was thinking very hard :

WARNING !!!!!! IF you open up the PSU be warned that the large Caps
can store a very dangerous Voltage. If your not familiar with This
stuff, leave it alone and buy a new PSU.


Indeed. As the o/p has already managed to squirt the wrong oil into it.
I'm surprised so many others here advocated opening the thing up. And if
he waas familiar with this stuff, I doubt he would have uses WD40 in the
first place.

If the fan is soldered to the PCB, I would not
attempt to replace the fan.

If the fan uses a connector, you may be able to
unplug the connector. The most dangerous part,
is trying to use tools to torque the connector
to get it loose. If a tool slips off, it could
hit a high voltage item.

In any case, this is one reason the fan connector
is on the periphery of the PCB and not in the
middle of it. You don't have to get "up close
and personal" with the main cap, to change out
a fan.


There is as much danger in making the main caps
"safe", as there is in working around the main

To see which caps are dangerous, there is a sample
schematic here. Modern PSUs don't use the same
architecture (they do double forward conversion),
but in terms of safety issues, this is a good


Capacitor C5 and C6 are larger devices (tin cans),
which are charged to 300VDC or higher. If you work
out 1/2*C*V^2 , the number of joules involved
is similar to that of a microwave oven cap.
*Do not* stick a screwdriver across the two
wire ends of a C5 or C6 cap, as the noise
is loud enough you could lose an eardrum.

1/2 * 0.000470 * 300 * 300 = 21 Joules

Resistor R2 and R3 are bleeder resistors. They're
in the circuit, to drain C5 and C6 after about
an 8 minute delay. That's a safety feature.
If we didn't need safety, R2 and R3 would not
even be in the circuit. They only have one
reason for being there. (I count waiting five
time constants as being long enough.)

But technicians working on a circuit like this,
assume R2 and R3 are defective and have gone
open circuit. And they further assume C5 and C6
are fully charged (it's a bit like defusing a bomb).
If a technician wanted to solder something on
the bottom of the PCB of the power supply, they
would use an *external* bleeder resistor to quietly
(and slowly) discharge C5 and C6. There is always
the danger of getting a shock, while making the
caps safe! (If you make a bleeder, you make yourself
some Plexiglas handles to position it, and
so on.)

If I see that the fan connector is "off to the side"
and I can work on the low voltage fan connector
without getting near C5 and C6, I'll do that.
If the fan is soldered to the PCB, I would probably
decline to work on the project and just buy a new PSU.

I only got one decent shock in all my time
doing electronics. I got my "teaching" shock as a kid,
working with an ignition coil. One minute I was
at the workbench, the next minute I was getting
myself off the floor, and I apparently had
jumped backwards and hit the floor when the
shock got me. I'd laid something on top of some
wires, and didn't see a HV wire underneath something
else, and that's how my little experiment "got me" :-(

I've worked on high voltage since then, with
no other incidents to report. For example, I
have a flyback circuit with a tripler on the output,
for HV work, and that circuit has never managed
to get me. It would likely burn as much as shock.
But the reason I've not had a shock since, is
the first lesson was *the best* :-) You couldn't
ask for a better lesson. I presume I passed out
for a moment, but I'm not really sure. Because
I don't know exactly how I hit the floor.

Some of my other experiments as a kid, did more damage.
That one wasn't the worst. A good lesson is one
you learn without bleeding or a concussion.


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
More or less safe to turn off power supply rocker switch? Nicholas Dreyer General 16 April 17th 10 07:14 PM
Computer won't turn on, power supply squeals Ben[_2_] General 5 May 26th 07 04:53 PM
PC won't turn on. It seems it isn't a power-supply problem.. phl0w Homebuilt PC's 3 April 22nd 06 08:05 PM
PC won't turn on but not a power supply problem? Please Help.... [email protected] Homebuilt PC's 6 March 19th 06 04:04 PM
How to make it faster? pete General 23 July 10th 05 06:45 PM

All times are GMT +1. The time now is 04:35 PM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 ComputerBanter.com.
The comments are property of their posters.